Company Blog
High quality high performance excellent service
Search productSearch post
High quality high performance excellent service
About 2,700 words · 14 min read
A lithium battery shipment can clear customs and still get stopped — by an airline that rejects the booking, by a marketplace that pulls the listing, or by a provincial electrical inspector who will not let the product be installed. For importers and engineers buying rechargeable lithium batteries from Asia for the United States or Canada, the paperwork falls into three separate layers, and they are owned by different people at different moments: dangerous-goods transport documents, market-access safety evidence, and ordinary customs entry documents.
This guide walks through all three, then breaks down which documents matter most in four common buying categories: a portable power station battery, a battery for sports cameras, a battery for dash cameras, and a high C-rate RC LiPo battery. Where a requirement depends on the exact model, channel or regulation edition, this article says so instead of giving a number you would have to re-check.
Most delayed shipments are missing one of the first four items below. Treat the table as a starting checklist and confirm the details against your own product, route and channel.
| Layer | Document or evidence | Who usually asks for it |
|---|---|---|
| Transport | UN 38.3 test summary for the exact cell and battery model | Carrier, freight forwarder, airline, in-country consignee |
| Transport | Correct UN number and packing instruction (UN3480/3481, PI 965/966/967, or IMDG for sea) | Carrier, dangerous-goods acceptance staff |
| Transport | State-of-charge record when shipping lithium-ion batteries by air | Airline, forwarder |
| Transport | Shipper’s declaration, lithium battery mark, Class 9 label, terminal and short-circuit protection | Carrier, Transport Canada / US DOT inspectors as applicable |
| Market access (US) | Safety test reports to the relevant UL or IEC standard; NRTL mark where required | Retailer, marketplace, insurer, end customer |
| Market access (CA) | Certification mark from an SCC-accredited body (CSA, cUL, cETL, cMET, QPS) | Provincial electrical authority, retailer, distributor |
| Customs | Commercial invoice, packing list, HS classification, country of origin, importer of record | CBP / CBSA, customs broker |
Lithium cells and batteries are Class 9 dangerous goods. Before they can be transported, the cell or battery type must pass the eight tests in Section 38.3 of the UN Manual of Tests and Criteria — altitude simulation, thermal cycling, vibration, shock, external short circuit, impact or crush, overcharge, and forced discharge.
Since 1 January 2020, the documentation requirement tightened: manufacturers and distributors must make a test summary available, not simply state that the test was passed. The summary is defined in subsection 38.3.5 and must contain, among other items, the manufacturer and test laboratory names and contact details, a unique test report identification number, the report date, a description of the cell or battery including mass and watt-hour rating or lithium content, the model number, the list of tests performed with pass/fail results, a reference to the Manual edition used, and a signature. The requirement applies across air, sea, road and rail.
Two points are worth keeping straight. First, a UN 38.3 test summary is transport design-type evidence, not a product safety certification — it says nothing about whether a finished device is safe to sell. Second, the summary must match the model actually being shipped. A change of cell supplier, capacity or mechanical design generally creates a new reference that needs its own file.
Classification drives everything downstream — packaging, labelling, quantity limits and whether a shipment is accepted at all:
Batteries shipped alone under UN3480 are fully regulated by air and are not carried as cargo on passenger aircraft; they move on cargo aircraft only. The watt-hour rating, together with the packing instruction (PI 965, 966 or 967 for air), determines which section applies and how much documentation is needed.
For lithium-ion batteries shipped alone under UN3480 by air, consignments are prepared at no more than 30% of rated design capacity unless the authorities of the state of origin and the operator grant approval. Recent editions of the IATA Dangerous Goods Regulations have extended reduced-state-of-charge expectations to some UN3481 shipments packed with equipment, so confirm the current edition and your carrier’s variations before booking rather than relying on a figure from memory.
Practically, the factory needs to measure, record and be able to show the state of charge at packing — which is one reason importers of larger packs often ship by sea instead.
In the US, the Hazardous Materials Regulations administered by DOT/PHMSA govern lithium battery transport, with the lithium-specific requirements in 49 CFR 173.185, which incorporates the UN 38.3 test requirement. Shippers take on classification, packaging, marking, labelling and training obligations, and the consignee’s own receiving procedures may add conditions.
Transport Canada regulates the classification, documentation, labelling, packaging and training requirements for handling, offering for transport, transporting and importing lithium batteries in Canada. All designs and types must meet the UN Manual of Tests and Criteria. Air shipments into Canada must comply with the ICAO Technical Instructions plus additional TDG requirements (Part 12); marine shipments fall under Part 11. Transport Canada also notes that damaged, defective or recalled batteries must not be transported by aircraft.
One practical difference from the US: under the TDG Regulations, the information required on a shipping document must be legible and in English or French. If your documents, labels and instructions are being prepared for the Canadian market, raise the bilingual question early — particularly for Quebec — instead of discovering it at the warehouse.
A safety data sheet supports hazard communication and emergency response, and many carriers and buyers ask for one. It is not a substitute for the UN 38.3 test summary, and — this catches people out — an SDS alone does not prove transport compliance.
Federal law in the US does not impose a single pre-market battery certification for most general consumer and industrial batteries. What actually gates the sale is a combination of standards, channel requirements and liability exposure. In practice the standards below are treated as mandatory by marketplaces, retailers and insurers:
The most common failure here is picking the wrong standard. A cell-level UL 1642 report or a pack-level UL 2054 report does not demonstrate that a finished power bank with output ports was assessed as a product. If you are buying a portable power station battery for the US channel, ask specifically for the finished-product report, not the cell report.
Two other items appear on US checklists often enough to plan for: FCC Part 15 obligations if the product contains a radio or in-scope switching circuitry, and California Proposition 65 warning obligations for products sold into California. The CPSC also maintains general consumer-product safety authority and publishes guidance referencing relevant battery standards.
Canada has no single federal “battery certificate,” and it is a mistake to describe CSA as universally mandated. What exists instead is a layered system:
Health Canada has been developing proposed mandatory safety requirements for lithium-ion batteries and consumer products containing them under the CCPSA. Treat any such proposal as not finalised until you verify its current status directly with Health Canada, and do not build a launch plan on it as though it were in force.
This layer is ordinary import administration, but lithium batteries add two details. First, HS classification — lithium-ion accumulators are generally classified under heading 8507.60, but the correct ten-digit code and any duty treatment depend on the specific product and should be confirmed with your broker rather than copied from a previous shipment. Second, marking: batteries and packages carry the lithium battery mark, and the watt-hour rating must be shown where required. A mismatch between the Wh figure on the specification sheet, the label and the UN 38.3 test summary is one of the fastest ways to get a shipment held.
The documents are the same in principle, but which ones carry weight shifts with the configuration and the energy rating.
| Product category | Typical configuration | Documents that decide clearance |
|---|---|---|
| Portable power station battery | High energy, often LiFePO4 or NMC; shipped alone in most cases | Usually UN3480, so air freight means the 30% state-of-charge rule and cargo-aircraft-only handling — most importers ship by sea. Finished-product safety evidence (UL 2056 for consumer power banks, or the storage standard applicable to the design) plus a Canadian mark from an SCC-accredited body. This category carries the heaviest documentation burden of the four. |
| Battery for sports cameras | Small single-cell or multi-cell lithium-polymer pouch packs, often 3.7 V, with a JST or similar connector | Typically UN3481 when packed with or contained in the camera; low watt-hour ratings may fall in a lighter section, but that depends on the actual rating. UL 2054 or IEC/UL 62133 evidence, plus a specification sheet that states capacity, dimensions and cycle-life conditions the buyer can verify. |
| Battery for dash cameras | Installed in a vehicle, exposed to high cabin temperatures in summer and cold starts in winter | UN3481 in most cases. The document that most often decides the sale is the temperature specification: documented charge and discharge temperature limits, and whether a high-temperature cell option is used. If the kit ships with a hardwire kit or charger, the charger is assessed separately. UL 2054 or IEC/UL 62133 evidence as with other small packs. |
| High C-rate RC LiPo battery | Multi-cell polymer packs in 7.4 V, 11.1 V and higher classes, rated for very high continuous and burst discharge | Continuous and burst C-rate must appear on the specification sheet, because it is both a safety-relevant parameter and the number the buyer is actually purchasing. Watt-hour rating is nominal voltage × amp-hours, and larger packs cross thresholds quickly, making them fully regulated. Terminal protection, short-circuit prevention and state-of-charge records for air shipments are the usual friction points. |
Where a product family spans several ratings, keep one document set per model rather than a generic folder for the category. That is what acceptance staff and auditors check against.
KBT (Shenzhen Keep Better Tech Electronics Co., Ltd.) is a Shenzhen-based rechargeable lithium battery manufacturer founded in 2009, serving distributors, importers, equipment manufacturers, private-label brands and system integrators in North America through standard models and OEM/ODM projects. The portfolio spans lithium-polymer packs, cylindrical cells and packs, lithium-ion packs in 3.7 V through 36 V classes, high-discharge RC packs, and larger LiFePO4 energy-storage batteries — the categories behind the four product types above. Relevant starting points include the large-capacity LiFePO4 energy-storage batteries, the high-discharge lithium-polymer RC battery pack, and 3.7 V protected lithium-polymer pouch packs with JST leads used in compact camera and recorder designs. The full range is listed under KBT rechargeable lithium battery products.
On documents, KBT’s own project support page states that available documents depend on the specific battery model and configuration, and that they may include UL, IEC 62133, KC, CE, CQC, REACH, RoHS, UN 38.3 and MSDS, along with other model-specific test reports — with the applicable set confirmed against the destination market and required standard before quotation. That is the right way to buy this: name the market and the standard first, then confirm the file, rather than assuming a certificate list transfers to your model. The engineering evaluation stage of the KBT battery project support process explicitly covers required compliance documents, and KBT arranges international lithium battery shipments including the accompanying documents, confirming packaging, routing, schedule and cost per order.
Do not assume a certificate listed for one cell family covers every pack built from it. A portable power station battery with an inverter and output ports is a different assessment from the cells inside it.
No. The test summary is transport evidence that the cell or battery type passed the UN design tests. A UL report addresses product safety against a UL standard for the cell, pack or finished product. Importers normally need both, and the applicable UL standard depends on which of those three you are buying.
Partly. Transport documents are largely common because both countries work from the UN framework — the differences are in the national implementation (49 CFR 173.185 in the US, the TDG Regulations in Canada) and in language requirements for Canadian shipping documents. Market-access evidence differs more: US channels generally want a UL or NRTL report, while Canadian provincial authorities want a mark from an SCC-accredited body. Some standards and marks, such as ANSI/CAN/UL standards and cUL or cCSAus marks, are designed to serve both.
The obligations scale with configuration and energy rating. A low-watt-hour battery contained in equipment is treated differently from a standalone high-capacity pack shipped alone. What does not change is the need for a matching UN 38.3 test summary and correct classification, plus whatever safety evidence your sales channel requires.
Under Canada’s TDG framework the consignor is responsible for preparing and providing the shipping document before a carrier takes possession, and US rules place comparable obligations on the shipper. In practice, which party performs that role depends on your Incoterms and on who is named as importer of record. Settle it in the purchase terms, not after booking.
The best time to resolve a compliance gap is during specification review, before tooling and before a booking exists. When you send an inquiry, include the application, voltage, capacity, maximum dimensions, continuous and peak discharge current, connector and wire requirements, quantity, target market — United States, Canada, or both — and the standards your channel requires. KBT confirms the applicable documents for the specific model before quotation.
Send the project details through the KBT contact page for a specification review, sample evaluation, or a quotation that names the documents included.
Category: Custom Battery Packs · About 1,700 words · 9 min read Industrial inspection tools and DIY electronics live in the same planning zone: the product needs a battery the market doesn't sell off the shelf, and the builder has to get it right ...
View detailsAbout 2,700 words · 12 min read Tags: medical device battery, lithium polymer, BMS protection, IEC 62133, IEC 60601-1, OEM battery pack Battery trouble in a medical device program rarely starts as battery trouble. It starts as one line on a spec s...
View detailsLearn how to specify a custom lithium battery pack for OEM projects, including voltage, capacity, BMS, connectors, cell type, UN38.3, MSDS, UL and CE.
View detailsExplore 24V lithium battery applications for ride-on cars, DIY speakers, and portable equipment. Define your requirements and request a quote.
View details